Filtertoleranz
#==================================================================================== # Civil - Einstellungen zur Geländeerstellung (siehe auch: Civil Variables (bentley.com) ) #========================================================================…
Triangulation Between Hydro and Topo Survey Data
I have a multibeam bathymetric survey and LiDAR around a caving stream bank, and the reality for most of it is that the bank probably has formed temporary shallow "caves" for much of it, though some probably did collapse between the two different survey…
PLAXIS 3D 2016: Fully parametric geometry
Application
PLAXIS 3D
Version
PLAXIS 3D 2016
Date created
30 September 2016
Date modified
30 September 2016
Introduction
Developments for PLAXIS 3D AE and PLAXIS 3D 2016 changed the internal structure of the geometry…
Converting triangulated surfaces in a CAD software for efficient modelling in PLAXIS 3D
Application
PLAXIS 3D
Version
PLAXIS 3D
Date created
06 June 2017
Date modified
06 June 2017
Triangulated soil surfaces usually contain a lot of irrelevant details for the intended analysis. This movie explains…
Inroads Triangulation - Deleted triangles
Hi,
I had copied a portion of surface containing features to a new surface. When i triangulate the clipped surface there are only less triangles visible. Around thousands of triangles are shown in "deleted triangle" column in the surface contents. Where…
OpenRoads Designer Exclude from Triangulation
Product(s):
OpenRoads Designer
Version(s):
10.04.00.48
Area:
Terrain
Question:
In previous versions of InRoads it gave the option for when creating the surface to exclude from triangulation, as I can tell in OpenRoads Designer…
TRIANGULATION
I a m using MX Road SS4. My doubt is, in this tool, is triangulation done based on Delaunay's Triangulation. Many triangles appear to be Silver Triangles in the tria model. Snapshot of tria model is attached for reference.
Terrain Modeling with Curve
Hello Good Bentley Community,
Once again I'm in a sticky situation here,
It turns out that I need to make a terrain (Surface or Mesh) using level curves, because I'm working on an academic project (for a good friend) that is located between mountains…
Controle de la triangulation
Objectif: fournir une triangulation conforme aux profils en travers.
Transverse Feature
Vous connaissez peut-être ce type d'objets pouvant être créés au moment de la création de la surface projet depuis le Raodway Designer. Cela ajoute au temps de…
Modelisation de Surface
Contrôle de la triangulation
La triangulation est basée sur les lignes contenues dans la surface. Souvent les surfaces ne contiennent pas de lignes représentant les profils en travers. Dans ce cas la triangulation peut ne pas donner une image identique…
Best Practices for adding survey data to an existing surface?
This has been discussed before but without any efficient answer I am asking it again in a slightly different manner. We survey large irregular property for a local municipality that requires MicroStation. These sites always require additional topo work…
OpenRoads Terrain Import / Update Keyin Help
Hi all,
We have an OpenRoads model that includes some linear templates and surface templates built from MX strings and triangulations. The intention is for us to update our MX string model and MX triangulation(s) and re-import the strings and update…
DTM Surface with non-contiguous triangulated areas
I have an InRoads DTM from survey data with a couple triangulated areas that don't touch each other. I have to get it to a client for use in Power Geopak.
Initially, the surface was triangulated with a 100 foot max triangle length to eliminate 'bad…
Combining MX Triangulation Models using Civil Terrain Tool
Process to combine two MX triangulation models into a single triangulation model using the Civil Terrain Tool
RE: [MX V8i] Merged triangulations
Chandru
The Data Acquisition tool is in the Task Panel as below.
In MX v8i SS3 the Data Acquisition tool has been replaced with the Civl Tools as below.
The Terrain Model tool can be used to import two MX triangulation models combine them and…
MX. Displaying and Analyising Spot Levels
Applies To
Product(s):
Bentley MXROAD
Version(s):
All Versions
Environment:
Any
Area:
Analysis / Display
Subarea:
String Names
Original Author:
Simon Pegg, Product Advantage…
RE: Road and alignment design (lidar data)
It sounds as if you are looking to have the lidar data imported as an MX triangulation model in MXRoad. MX can directly import Lidar data however it can often be too large so importing it as a Point Cloud is often a preferable import method. The wiki…
How to exclude an area of a model from a tringualtion analysis
Applies To
Product(s):
Bentley MXROAD
Version(s):
08.11.07.427, 08.11.07.494, 08.11.07.566, 08.11.07.494
Environment:
N/A
Area:
Analysis
Subarea…
How to Seed the Composite Triangulation Model
Applies To
Product(s):
Bentley MXROAD
Version(s):
N/A
Environment:
N/A
Area:
Analysis
Subarea:
Trinagulation
Original Author…
How to Create a Composite Triangulation model.
Applies To
Product(s):
Bentley MXROAD
Version(s):
N/A
Environment:
N/A
Area:
Modify
Subarea:
Triangulation
Original Author: …
Re: Help: Nearest points?
If you already have the points, and you just want to do a 'nearest two neighbours' triangulation, then it's not actually super hard.
This bit of script kinds of does what you want, but the result is so far from usable, that it'll be a fairly major…
Re: InRoads Triangles....New to InRoads
![Jason W. Smithey [Bentley Civil]](https://communities.bentley.com/cfs-filesystemfile/__key/communityserver-components-imagefileviewer/communityserver-components-avatars-00-00-00-21-72/4TFHLUWQ3890.jpg_2D00_24x24x2.jpg?_=636515530586704343)
If I understand correctly, you are just wanting to delete the triangles from your CAD file?
Go to Surface> Update 3D/Plan Surface Display. For Mode, select Display Off. Select the surface of which you want to remove the display of triangles. Toggle…
MX Ignoring points with in close vicinity during triangulation.
Hi,
I have created curb line with an horizontal offset of only 0.0001m offset and vertical offset of 0.15m, however when I am my triangulating design model it is ignoring kerb line which is exactly 0.15m high and 0.0001m offset. Warning I am getting…
Re: InRoads - Thin Surface
Todd,
Try using the Tools> Application Add-Ins> Thin Random Points command and see if it gives better results.
Thanks,
Jason Smithey
Tailoring Triangulation
This is Palanirajan from India, I am working in MX for the past two years, i have some queries regarding triangulation,
I had come across this option of Tailoring Triangulation which means an area of points can be isolated from triangulation with…