• OpenRoads

    Shawn McGaffick
    Shawn McGaffick
    OpenRoads Designer is a comprehensive and fully functioned detailed design application for surveying, drainage, subsurface utilities, and roadway design that supersedes all capabilities previously delivered through InRoads, GEOPAK, MX, and PowerCivil…
    • 1 month ago
    • User Success Onboarding and Adoption
    • Onboarding and Adoption Wiki
  • Best way to create utilities from many data points

    Kait W
    Kait W
    I have roughly 800 points with northing, easting, elevation, depth below grade, stationing, and offset from my alignment information. The depth below grade varies from point to point otherwise the solution would be quite simple. There are roughly 8-10…
    • 6 months ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • ORD Drainage and Utility. Pipe length not accurate when drawn.

    Reem Naser
    Reem Naser
    When i place a pipe the length will show 6' but when i use the measuring tool or element property for some reason the length is doubled. Any reason for this?
    • 7 months ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Is there a way to set the cover depth (with respect to active terrain) for utility (Electrical Conduit) once it has been created in OpenRoads ?

    Anzar Sajid
    Anzar Sajid
    I know that we can do this while using the command "Extract from Graphics", but, is there a way to reset the cover depth once after creation of the conduit.
    • 7 months ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • ORD - How do you show utility that are parallel to the center line in road profile

    Viviana Di Giovanni
    Viviana Di Giovanni
    Hello, I need some guidance on how to display utilities on the roadway profile. the way I've done it so far is by creating a profile run of my utility. However, this only works on one specific file, and I am not able to reference this file in the…
    • over 1 year ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Last Mile Utilities - Set of utilities for OpenRoads & OpenRail Designer

    Shashank Gokhale
    Shashank Gokhale
    Last Mile Utilities MDL Application - Set of utilities for OpenRoads & OpenRail Designer Product: OpenRoads & OpenRail Designer Version: CONNECT Environment: N\A Area: Programming …
    • over 1 year ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Wiki
  • Drainage and utilities - Extract Utilities from graphics

    Gunther Groenestein
    Gunther Groenestein
    Hello I'd like to put a 2D utilitiesmodel into 3D by extracting the graphics. There are a few issues I see: It isn't possible to add a diameter to the 3D element. It is possible through the description, but that is unlogic It isn't possible…
    • Answered
    • over 2 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Openroads: How to Display Existing Utilities in Cross-Sections?

    Yash Patel
    Yash Patel
    Currently, I have my existing utility lines in 2d view with a feature definition and plotted them at an assumed depth of 3' below existing ground in profile view and set as active profile. Typically, in SS4 and SS10 this worked in terms of displaying…
    • over 2 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Should I use OpenRoads to design water and powerlines for an OpenBuildings project?

    S. R.
    S. R.
    This is a general question about which Bentley product should be used: I need to create 3D models for underground utilities including: water lines (including fire hydrant connections), power lines, and CCTV. The entire project is a major building…
    • over 2 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum