Hello! I am a civil engineering student and I am having a hard time figuring out what type of connection STAAD Ram will be able to provide for truss structure like this one? I prefer to have those members be connected using a side-to-side plate. Please…

STAAD SPACE START JOB INFORMATION ENGINEER DATE 05-Dec-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 10 0 0; 3 0 5 0; 4 10 5 0; 5 0 0 10; 6 10 0 10; 7 0 5 10; 8 10 5 10; 9 1.66667 5 0; 10 3.33333 5 0; 11 5 5 0; 12 6…

I am using a square section by TATA STRACTRA one on top of another.

How can I change the size of my loading diagram?? it cannot be lessen it size my using the ctrl + mouse scroll.

Someone can teach me how to put a wall load over a slab without using any beam.

sabbir ahmed -static - 07.05.22.std SOMEONE PLEASE REPLY, Calculation sheet is not available as design has failed, why it is showing ? sabbir ahmed -static - 07.05.22_foundation.xml

this is the code STAAD SPACE START JOB INFORMATION ENGINEER DATE 09-Apr-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 0 12.085 0; 3 -1.05865e-015 0 5.763; 5 -2.11729e-015 0 11.526; 7 -3.17594e-015 0 17.289; 8 -3…

Section fails while designing section 5635.Project 1 new.std

How can I delete some supports? I have given support and nodes very close to another nodes and support by mistake. When I delete these wrong support, my file gets corrupt. Please help. 0677.Project 1 new.std

Hola tengo este problema en mi computadora, al asignar cargas muertas a mi edificio se producen estas áreas fuera del modelo que no me dejan trabajar, he buscado ayuda pero nadie me da una respuesta, aparentemente solo sucede en mi computadora por que…

Hi. I recently got access to the student license of STAAD Pro. It was working well until last few days. The application is not starting. Below given screen appears and then there is no further movement in the loading. I tried re-installing the application…

Good day, Can someone help me to fix this problem?

Hello, I had a question regarding this simple circular tunnel model shown below. I have the following modeled to check the shear SQY. I know I'm missing something simple here so I hope I can get some help. L=100 ft (total longitudinal length)…

I'm designing a concrete slab in STAAD. AT the end of the file, I have the following and would like to define the cover as 2.6": START CONCRETE DESIGN CODE ACI 2011 UNIT INCHES KIP FYMAIN 60 ALL FC 4.5 ALL DESIGN ELEMENT ALL CLB 2.6 ALL CLT 2.6 ALL…

Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…

Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?

I am trying to create an polygonal opening in a surface using parametric modelling approach but I am getting only one edge division along the edge of the opening. The divisions along the edge cannot be modified even if I set the divisions to a definite…

How to rectify this failure known as 'Detailing failure' in RCDC

Dear sir, I am doing the analysis of cable but the reactions are coming with an extreme value like 66kn along x. There is no any weight on the cable only self-weight is considered. Kindly explain to me why reactions are so conservative. Also, guide…

How do I change Mton/Cm to Kn/m

Hello, I have assign 3 connection in to one joint, i know we can generate drawings for each connection by double clicking it. But i want to know hence this is a one Joint, can i generate all the connection drawing in the joint?

Dear sir, In My attached fil,I am creating a deck slab to make my steel beams as a composite beams.But I notice deck slab somewhere missing the steel beams .some beams are not composite?Why it is happening?do I have to add that beams manually in stad…

Hi, I have a large STAAD model file for a linear analysis of a space frame. I have used the INACTIVE MEMBER/PERFORM ANALYSIS/CHANGE commands to sequence the framing as the loading is applied. When I run the analysis I get an error message stating…

Dear sir, In attached stad file. I am applying the dead load 2kn/m2 as floor load. 1.somewhere I am attaching two secondary beams with primary beams with the same node.is this load distributed all over the area same as 2kn/m2 or where I am having…

Hello, Is there any way that i can perform Fatigue analysis for steel member in STAAD.Pro? Thank you in advance