STAAD SPACE START JOB INFORMATION ENGINEER DATE 05-Dec-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 10 0 0; 3 0 5 0; 4 10 5 0; 5 0 0 10; 6 10 0 10; 7 0 5 10; 8 10 5 10; 9 1.66667 5 0; 10 3.33333 5 0; 11 5 5 0; 12 6…

I am trying to analyse an aluminium frame but sections to be used are not in database so I tried USERTABLE and made 2 sections First is 30x20x1.4 mm channel section and second is SHS 40x40x1.4 . After runing analysis it throughout an error as in subject…

An error is showing while updating the column design in RCDC as shown below. please provide the solution .

I am getting an error when creating a new project in Staad Pro it reads. Can i get some help ?? This application encountered a fatal error and must exit. Error: A task's exceptions were not observed either by Waiting on the Task or accessing its exception…

I have the subjected error, hereby i attached the staad file, please let me know why this occurs. thanks Stanley U70-D-0910_PIT_WALL_ONLY_RevA.STD

Hi Team, We found a bug while working on the staad connect edition. The staad file is attached for reference. Screenshots of results are attached herewith. The design demand for the section is very less compared to the actual capacity. However…

Hello Everyone For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…

Hello Everyone. I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?

unable to read analysis data from .mbd file in RCDC 9.0 from etabs 18.1.1 and etabs 16.2.1 also can not import edb file see the screenshots

Receiving the following error when attempting to design project for concrete: Can anyone help? One Bigelow After Rebuild.std

I am analysing an RCC box girder for which some peculiar tapered sections have to be created. I created a tapered rectangular section in AutoCAD 2014. I used polyline to create the 2D and then extruded it to make it a solid 3D section. Now when I import…

We have been trying to automate STAAD.Pro application through VB.NET coding. We need to run the STAAD.Pro application in the minimized window mode. Also, how can we handle STAAD.Pro warning message through VB.NET. Thanks in advance...

I have got my report, but there is no loading details like dead load, Wind loads and all... In report settings i have added Loadings, but its not showing.... Wt to do???? i want to see other load details. How to get that details?

Dear sir, when I getting error as "ERROR E VALUE ENTER IS DOESNT SEEN REALASTIC" please correct me if I done something wrong. refer attachments. Production Block-1(20062018) WITH ROOF -PU .STD

Dear All, Many a times while modeling in STAAD I get this error " above line contains erroneous data, data-check mode is entered ". I have checked my syntax but could not find any error. I request you all to please suggest what could be the possible…

I am working with a fairly large model consisting of a steel frame building with the floor modeled using plates connected to the beams. I keep getting the following error: ***ERROR - AT JOINT 2234 DIRECTION = MZ PROBABLE CAUSE NEGATIVE DIAGONAL…

Interactiver RC Design crashes everytime when I try to open a previously saved file. It only opens up after a new file/project is analyzed. One I finish designing and save it and exit the program, I cannot open it again to review my designs. Can any…

I'm modeling a 3 stringer short span timber bridge in staad. The model consists of the three beams and deck planks (which are modeled as Plates). All geometry, material properties, supporting, and loading have been assigned. There is only one error in…

I'm modeling a 3 stringer short span timber bridge in staad. The model consists of the three beams and deck planks (which are modeled as Plates). All geometry, material properties, supporting, and loading have been assigned. There is only one error in…

hello folks, When i run the staad file that i have attached in this post, i get an error message. "above line contains erroneous data" Can any gurus plz help me out with this model. > Is the error due to the application of floor load on…

I have been using STAAD Pro V8i (release 20.07.05.15) for multiple light structure analyses, and I have recently noticed an inconsistency in the software with regards to member load definition. It is apparent that my version of STAAD is performing…

Hi, STAAD v8i doesn't run analysis without MEMORY-command in input file. Output file then only contents of two lines: 1. STAAD SPACE ERROR NOT ENOUGH MEMORY TO START ANALYSIS. ( 41 ) But available memory should be enough. We tested…