• PB with extraction DEM

    pjf
    pjf
    Hi i have a pb when i extract. i'am going to migrate from V8 2004 + TRIFORMA to 8I + Arhitecture. My pb is that the DEM don't calculate me some cells and i don't know why. I attach a file with some cells and a drawing def. This cells are calculated…
    • Cellules.dgn
    • over 12 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • Re: PB with extraction DEM

    pjf
    pjf
    No sorry, i don't know. no Knowledge in program. I have just make a config from V82004 to V8I and make some basics macro. i am just a little Draftsman who have pb to work in 3D because somethings (i expose that in a message before) that work in triforma…
    • over 12 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • PCS Part Assignment Not Recognized in Extraction

    josh ray
    josh ray
    I have successfully added a part assignement to the component Door_Elev_HingLeft_Comp_1 and 2 in Parametric Cells Studio.. I have added this part assignment to get the door swing elevation marker to show up dashed. When I place the door into the model…
    • over 14 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • Re: BV, DV and detail of design

    pjf
    pjf
    Hi i have read your messages and allow me to ask a question (SS2 + Architecture). In V8 2004, i have use DEM and it was very long to calculta my 2d. we are going to use V8I SS2. we have remake our config. We have pb to make extraction with the DEM…
    • over 12 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • Urgent : Crossing from Triforma to V8I + ARCHITECTURE

    pjf
    pjf
    • over 12 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • Plan Door Swing in PCS

    josh ray
    josh ray
    I have been updating door in Parametric Cell Studio. The questions I have are about the plan view of the door swing. The first question I have has to do with adjusting the door width. When I adjust the door width it does not scale the Plan Door…
    • over 14 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • Re: PB with extraction DEM

    pjf
    pjf
    Hi emilberger Today i have expose my pb to Bentley and i hope some answer. So the general pb is how to work in 3D in architecture. Make a draw in 3d, no pb (or not yet..lol no). But the pb is to make extraction. With the DEM, many cells are not…
    • over 12 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • Updating Doors in Parametric Cell Studio

    josh ray
    josh ray
    When modifiying and/or building new doors in PCS you can put an Elevation Door Swing Marker onto the door so that when it is extracted in bentley it will show which direction the door is to open. Is it poosible, and if so, how do you change the Elevation…
    • over 14 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • URG : Problems crossing TRIFORMA to Bentley ARCHITECTURE

    pjf
    pjf
    • over 12 years ago
    • OpenBuildings | AECOsim | Speedikon
    • OpenBuildings | AECOsim | Speedikon | Forum
  • View related content throughout OpenBuildings | AECOsim | Speedikon
  • More
  • Cancel