• Bolt-Length Calculation [OPM – 10.07.00.32]

    Florian S.
    Florian S.
    Hello everybody, For your convenience, a “too long did not read”: I think the algorythm to choose a correct bolt length is not working correctly together with the Increment value “BOLT_INC”. It produces wrong values and does not represent the way…
    • over 3 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: Replaced Bolts using Fix Disconnects

    Rahul Kumar
    Rahul Kumar
    Hi, 1. You can check first by creating iso sheet again and verifying it inside iso sheet manager if sheets created successfully. 2. In intermediate file, check if fasteners available or not. Are there only Bolts which are not appearing or gaskets…
    • over 6 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • Gaskets and Bolts on end of line valve appear on continuation isometric

    Luis Barbiero
    Luis Barbiero
    Good Day, We have 2 lines with the following components: Line 1 consists in a Pipe, Flange, Gaskets/bolts, Valve, Gaskets/bolts Line 2 consists in Flange, Pipe The connection between line 1 and line 2 are line 1 Gaskets/bolts and line 2 Flange…
    • Answered
    • over 6 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • AutoPLANT Modeler, Lined Pipe, Bolt Calculation

    S. Hotte
    S. Hotte
    Hi, AutoPLANT Modeler SS7r1 (.239) Lined Pipe Module Bolt calculation is not done when inserting two fittings. Works fine when something is in between the flanges. Calculated Bolt Length is set to Yes SH
    • over 6 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: What's the bolt/gasket selection rule at spec break

    Harpreet Singh
    Harpreet Singh
    Hi Changsong, It queries bolts and gaskets from the spec of mating flange. In case of nozzle, it will query the bolts and gaskets from the spec of flange being placed. Is there any different behavior on your side or any error message? Regards, Ha…
    • over 6 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: Is there a easy way to select all bolts which used on different end preparation in OPM?

    Rahul Kumar
    Rahul Kumar
    Thanks to confirm Changsong, There is a wiki article to refer similar content. http://communities.bentley.com/products/plant/design___engineering/w/plant_design_and_engineering__wiki/29496.how-to-update-bolts-and-gaskets-in-openplant-modeler I am…
    • over 6 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • RE: Bolt Length cannot be calculated

    Harpreet Singh
    Harpreet Singh
    Hi Changsong, We have several wiki articles on Bolt Length calculation which will give you an idea on how is bolt length calculated. One of them is given below: http://communities.bentley.com/products/plant/design___engineering/w/plant_design_and_engineering__wiki…
    • over 7 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • How to prepare Catalogs of hexagon bolts, hexagon nuts and washers

    Przemysław Chmura
    Przemysław Chmura
    Hi all. I've got a problem. I've prepared weld neck flanges and blind flanges catalogs. Now I should prepare catalogs of bolts, nuts and washers suitable to my flanges catalogs. I found only these components about "bolts", but nothing more (nuts,…
    • Answered
    • over 8 years ago
    • OpenPlant | AutoPLANT
    • OpenPlant | AutoPLANT Forum
  • View related content throughout OpenPlant | AutoPLANT
  • More
  • Cancel