Have this situation where I'm installing MicroStation v8i SS4 (08.11.09.832) and InRoads Group v8i (08.11.09.789) together on a new system. After installing successfully with no errors, I attempt to launch InRoads but receive an error message regarding…

It seems fine at the physical computer (I was using it earlier today), but when I use Bentley InRoads Suite SS4 (MicroStation SS4) through a remote connection, the top of the Tasks dialog box is bigger yet empty, not allowing me to change tasks with a…

Hello everyone, I have just installed InRoads to begin creating some plan and profile sheets, however, when I open a DGN from ProjectWise, I am receiving the following error messages: I am relatively knew to MIcroStation, so could someone help…

I am unable to import .LAS file as point clouds in Microstation SS4. Each time it says "Convert Failed". I used to be able to use Data acquisition in previous versions but can't find that tool anymore. Since migrating to ss4, it been confusing on how…

Hello all, I installed the current version of InRoads (ir81109918en.exe) on top of my MicroStation V8i SS4 V08.11.09.862 running on a Workstation with Microsoft Windows 10. The Installation of InRodas works fine and finished without any error message…

Hello, I have an existing alignment that I am using as a center line to cut my cross sections, and I have a second alignment (edge of road) that I need to show as a point on the cross section. I need to show the distance and elevation of the second…

Please tell me there is an autosave feature in InRoads V8i. I am so used to MicroStation autosaving every 60 seconds I sometimes forget to save my work often enough in InRoads. Thanks. Michael Greene

I'm working on a project where I have a lot of spot elevation callouts and text masking is necessary. When I place the plan note, the text mask it there, no problem. But when I've had to update the notes recently, the text looses it's mask. When I update…

My company is trying to develop a way to utilize the intelligent Civil 3D Pipe Networks, but we are required by most of our clients to display all of our data in a 3D model in Microstation. I am trying to create a workflow to convert Civil 3D 2012 Pipe…

I am looking at calculating time of concentration in InRoads Storm & Sanitary. Using the FAA method, you are asked to give K1, which is stated as a "regional constant". Where can I find the relevant regional constants? Thanks, Jenna

MicroStation version 08.11.09.292 InRoads version 08.11.07.566 With particular geographic coordinate systems assigned, the Auxiliary Coordinate System and InRoads compute latitude and longitude differently and display different results (see table…

After installing MicroStation SS3 v08.11.09.397 and InRoads SS3 v08.11.09.493 I am not seeing any of the Civil commands in my task menu. The machine I am installing on as a VMWare virtual machine (whilst we evaluate it) running Windows 7. I have tried…

Just curious, thanks in advance... Using MicroStation V8i SS3, V08.11.09.397. InRoads V8i SS2, V08.11.07.615. Multiple sections, files, and users experiencing the same issue. After creating a storm system SDB for a proposed drainage network, I'm…

Hello there, The issue is that when I create new cogo points, In-roads provide a text with Easting, Northing and Elevation in the default level. Is there any way to turn off/on this feature??? Thanks & Regards

I am using MicroStation V8i (SS2) InRoads (SS2) and need to adjust some cogo points elevations by a specific distance. For example, if I have a group of points with different elevations that I would like to raise or lower by 3" is there an easy way to…

Yesterday I had my Microstation V8i updated to version 08.11.07.171. We also changed to a new workspace, so my config files are different than they were Wednesday. After the update: When I start InRoads from a desktop icon or from the start menu…

Please forgive my lack of knowledge of InRoads, but we only have to deal with it here and there. We received a survey that was done with InRoads, and one of the files we received is the Topo file, which is a 3D DGN with the points and line strings displayed…

Hi guys, My boss has asked me to look into this one. A Contractor on a recent job informed him of receiving a Cross-Section package of 11x17 drawings with each cross section on each individual sheet, containing all volume and annotation information…