• Cut/Fill Split for each layerwork component [ORD]

    Warren McLachlan
    Warren McLachlan
    Hi In ORD 2019 R1, how does one split up the cut and fill quantity reported for a layerwork component? i.e. the amount of material that has to be cut in order to place a component and how much of the component is in fill. Pre-OpenRoads GEOPAK was…
    • over 4 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • OpenRoads Designer: How to calculate volumes of overlapping template drops?

    Max Suijkerbuijk
    Max Suijkerbuijk
    I am trying to calculate volumes of different layers of asphalt and different layers of groundwork. I've created a template which contains all these layers, where the final groundwork layer is variable (slopes and ramps or not). In my template this layer…
    • over 5 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Bentley Navigator Measure Volume Issue

    Chris Compton
    Chris Compton
    I have an Openroads model that contains an IFC element imported via Aecosim. It looks great in Openroads and Navigator but there is a discrepancy with the volume of the solid being reported. The volume is correct in Openroads. But when I measure it…
    • over 5 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Is there a way to find the volume between 3 terrain models? Or two terrains below a plane?

    B Jassin
    B Jassin
    Hello, I need to find the volume between two terrain models but also restricted by a plane elevation (floodplain). Is there a way to accomplish this with PowerGeopak? Thanks! Ben
    • over 5 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • By Open RoadsDesigner, how to separately calculate the earthworks volume?

    Zhengpeng Chen
    Zhengpeng Chen
    Hi, In Open RoadsDesigner, how to separately calculate the earthworks volume? The model has 3 terrains (existing top surface, strong weathering rock layer, and medium weathering rock layer). See the following screenshots: But, in the Component…
    • over 5 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • How to Set up Unsuitable Materials based on Designed Terrain instead of Existing Terrain

    Edip Ahmet TAŞKIN
    Edip Ahmet TAŞKIN
    I try to set unsuitable materials referenced to designed terrain model instead of existing terrain in End-Area Volumes. Although I edited settings of unsuitable material's feature from existing terrain to design it is still the same. I would like…
    • over 6 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Volume from mesh

    David S
    David S
    I'm trying to figure the volume between two meshes (excavation for bridge pier). I've created one mesh for the excavation limits which extends (upward) to the existing ground surface (meeting the Level: Terrain_Ex_Calc_Triangles_GS), the other mesh is…
    • over 7 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Pull Volumes from Corridor

    Josh O
    Josh O
    I am attempting to pull quantities from a corridor I have created. The corridor consists of various fills. I am relatively new to InRoads so this may be far more simple than I am making it. The below image shows what I have created.
    • over 7 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Surface Triangle Volume with Shapes including Holes

    Chris Finn
    Chris Finn
    Anyone know if there is a way to use a shape with a hole in it to compute the triangle volume between surfaces? If we need to differentiate cut/fill by areas like this, the only way I can see to do it is use two shapes and then a secondary calculation…
    • Answered
    • over 7 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Power InRoads Analyse Volume

    mocha
    mocha
    Hi, I've been requested to find out the cut volume of an area of the sea bed that is to be cut down to a certain depth with a cut slope of 1:5 and 1:3. Same area location but different slopes. I've created the end-condition template for the slopes,…
    • Answered
    • over 8 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Using inroads to calculate volume

    Carlos Leon
    Carlos Leon
    I'm pretty sure I've done this before and I simply cannot remember the sequence of doing so. I have a base topo and am overlaying a final fill plan. Wanting to calculate the remaining fill, normally I'll calculate the area of each 5' contour in sq.ft…
    • over 9 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • gridded volume in PowerCivil for country

    Vivekhanandam  DPK
    Vivekhanandam DPK
    hi, I want to generated grid and show the volumes in the grid, right now we get as a text file! is there a method to create a dgn, with grid and volume of each grid! awaiting reply. regards, vivek
    • over 11 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Re: [MX V8i] Volume calculating

    aleksander_zamorski
    aleksander_zamorski
    Scott, If my way of thinking and understanding is right the temporary section area used to volume calculation between two sections will be determined as on drawing below (between two dotted lines - only in limit where both sections are present one…
    • over 13 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • InRoads V8i SS2: Component Volumes

    Lucy Jiang
    Lucy Jiang
    I am trying to create a volumes report using end area volumes. When I use Component Quantities from the RoadWay Designer, I can get all components quantities, but when I using End_Area_Volumes from the Cross Sections and used the Volumes as style sheet…
    • over 11 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Re: [MX V8i] Volume calculating

    aleksander_zamorski
    aleksander_zamorski
    Hello Wolfgang, I have did it other way because I really have little time for experimenting :( I made a little cheat: I have done a two models of section - 1-st from design (which is triangulation model) and 2-nd from subgrade (string model). I got…
    • over 12 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • InRoads V8i: The roadway designer components are not displaying in the cross sections

    olymplic
    olymplic
    It maybe simple, but since I am new to InRoads, I would appreciate your help.... Please see the screen shot below, the road components are not shown on the cross sections. I have tested using different templates, sometimes the components are shown…
    • over 12 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • Reporting a road that has a civil cell

    Andrea Garecht
    Andrea Garecht
    (Filed for a user) Using as an example a road that has a civil cell at a intersection, how can I integrate the cell within the corridor in order to report the offsets and to get the volume quantity. Thank you, Andrea Garecht
    • Answered
    • over 10 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • need to learn how to creat template for cut and fill

    murtaza gul
    murtaza gul
    hi every one, I need to learn how to create template from scratch (have used them in past but never created or amend one), the template will be for different cuts and fills, different types of ground condition etc, also to calculate cut and fill volumes…
    • over 9 years ago
    • OpenRoads | OpenSite
    • OpenRoads | OpenSite Forum
  • View related content throughout OpenRoads | OpenSite
  • More
  • Cancel