staad pro update 12
Does anybody tell me in staad update 12 I m going to assign a circular section but after design when I double click on the section than it is showing a rectangular shape why?????
RAM ELEMENT
Dear Sir
Good day.
I'm a new user of RAM Element, I have a query as per below :-
I do modelling and run analysis using RAM Element, after that directly design pad footing using module tools.
From the report and analysis, where should I check whether…
Fundamental time period of bridge pier
I want to calculate fundamental time period (eigen value method, using command MODAL CALCULATION REQUESTED) of bridge pier in staad pro using lumped mass in long & Trans direction as per IRC 6 & IRC SP 114.
I am enclosing the details . I think there…
STEEL ROD AS BRACING IN STAAD PRO CONNECT EDITION
I have model my truss and i want to add steel rod of 20mm diameter as a bracing on pipes carrying the truss,is this option available in Staad Pro Connect Edition?
3D STEEL TRUSS DESIGN
I want to design this kind of steel truss in Staad Pro Connect Edition, should i run analysis in staad space or staad plane which one is correct?
LINE LOAD ON ANALYTICAL MODEL STAAD PRO CONNECT EDITION
Addition of partition wall load on slab should be added on analytical model in Staad Pro Connect Edition
PROJECT OF FLAT SLAB, WITHOUT BEAMS STAAD PRO CONNECT EDITION
Option for modelling,analysis and design of a project with flat slab should be added in Staad Pro Connect Edition
CANTILEVER SLAB IN RCDC
Design of cantilever slab in RCDC should be added and also slab supported by beams on its two sides and its other two sides free or only three sides are supported by beams and the other side free.
DEFLECTION CHECK OF RCC PLATES (RAMP)
Iam designing a reinforced concrete ramp as a plate,the difficult iam facing is there is no BS 8110 in analytical design,and with the available BS 8007 i cant check deflection of the plate.
BS 8110
BS 8110 should be added currently is not available in design at analytical modeling ,the BS available for concrete is only BS 8007.
ADDITION OF LINE LOAD ON PLATE
Option for adding wall load (partition wall) as line load direct on slab should be added
RCDC ERROR WHILE DESIGNING BEAM (STAAD PRO CONNECT EDITION UPDATE 5)
During design of beam in rcdc,if i put a check of crack width the software will not design and it gives a message written "Cannot find column [StAstTop] but if i dont check for crack width the software works perfectly.Need a help on this problem because…
RCDC ERROR WHILE DESIGNING BEAM (STAAD PRO CONNECT EDITION UPDATE 5)
During design of beam in rcdc,if i put a check of crack width the software will not design and it gives a message written "Cannot find column [StAstTop] but if i dont check for crack width the software works perfectly.Need a help on this problem because…
CONCRETE GRADE SELECTION IN RCDC
I think it will be better during design in RCDC,to select the concrete grade of column separately from that of wall.Concrete grade should be divided into two parts one for columns and the other one for walls.
PARAMETRIC WALL FOUNDATION DESIGN
May you please improve the design of foundation of parametric wall in RCDC,lets say if i want my footing size to be 1500mm by 300mm depth,but the left side i want it to be 400mm from centre of wall and right side to be 1100mm from centre of wall,currently…
FLOOR LOAD FAILURE
Improvement should be done on RC wall, during modelling on places of RC wall i don't place beam on top of the wall because the wall it self act as a beam,but when it comes to assign of floor load in places where there is no beam on RC wall the floor load…
Stirrup strength
May you add an option for choosing the strength stirrups in RCDC,by default is 250 but when i want to use stirrup of 410 its not possible to change its strength in RCDC
COMBINED FOOTING, RAFT FOOTING IN RCDC
May you please include the design of raft foundation and combined footing in RCDC
SLANT BEAM DESIGN IN RCDC
May you please update the design of Slant beam in RCDC,as you may have a building has a certain slope from one grid to another
FLAT SLAB, RIBBED SLAB AND WAFFLE SLAB
May you please include the design of waffle slab, ribbed slab and flat slab in rcdc
Design of Solid slab (Conventional slabs)
Hello Everyone
For a while, I was using an Advanced Concrete Design (RCDC) for the design of a solid slab. Today I tried to learn the RAM concept for the slab designs but I saw a design of strips that had never seen before (When I was using RCDC and…
Dummy beam
Hello Everyone.
I create a dummy beam with density=0 and E=0 (Figure.1) then I assign the beam (Figure.2) then Staad Error occurs( ***ERROR*** MATERIAL NAME MUST NOT CONTAIN ANY BLANK SPACE )(Figure.3), What is the solution?