1.0 In staad why I am getting more reinforcement in top column (See bemm no. 76 & 77) see the attached model. 2.0 What parameter need to use so that reduction factor is not considered in design calculation because as per is 1893-2016 it is only use…

Dear All, Could anyone help me to delete existing primary load cases in openstaad ? because every time I do the analysis, loads repeat instead of replacing the previous load case. Here is my code: Sub GenerateModel() Dim cx(1) As Double Dim cy…

Dear All, It has been so long since I first asked this question with no answer. Is there any way to delete existing load cases in openstaad or at least clear STAAD editor? because every time I do the analysis, loads repeat instead of replacing the previous…

Hi all, I am trying to delete existing load cases - primary and combinations from an existing file using openstaad . But there are no functions to delete the existing load cases, can anyone tell me how to do this in openstaad . Thanks

STAAD SPACE START JOB INFORMATION ENGINEER DATE 05-Dec-22 END JOB INFORMATION INPUT WIDTH 79 UNIT METER KN JOINT COORDINATES 1 0 0 0; 2 10 0 0; 3 0 5 0; 4 10 5 0; 5 0 0 10; 6 10 0 10; 7 0 5 10; 8 10 5 10; 9 1.66667 5 0; 10 3.33333 5 0; 11 5 5 0; 12 6…

Hi Everyone, What command can I use to clear everything in the STAAD file using OpenSTAAD.

HELLO EVERYONE, MY QUESTION IS WHEN I COMPARE TWO MODELS ONE WITH OFFSET COMMAND AND THE OTHER WITHOUT OFFSET AND IN BOTH MODELS I M GETTING DIFFERENT RESULTS WHY??? 1.0 Steel requirement in the top column is less in the offset model as compared to…

Dear Friends, The script below is for a very simple model (single member). I'm trying to assign a steel tapered section (200 5 800 150 10 150 10), but I'm facing some troubles. Could you help me with the script? Sub GenerateModel() Dim cx(1…

IF THE ORIENTATION OF THE AXIS LIKE SHOWN IN THE FIGURE THEN MX REPRESENTS THE VERTICAL MOMENT AND MY HORIZONTAL AM I RIGHT OR WRONG PLEASE CORRECT ME.

Hi, I have a question regarding column deflection and sway in STAAD. The below picture shows the deformed shape of a column subjected to lateral forces in a frame. I know the maximum sway/drift in STAAD is gotten from the node displacement value (translation…

Hi there, please I am working on a steel frame design that includes OWSJ in the model. I have tried various forms of releases for the joist members like assigning truss parameter to the diagonals and verticals, releasing moments at the ends etc. but when…

Why am I facing this issue again and again?? APPROACH BRIDGE CHURHAT.STD

Hi there, I'm modelling a steel frame in STAAD and looking to include c channel girts in the model. The girts (red lines) are to be located on the front face of the column with wall panels (green line) attached as shown below. I plan on using meshed…

How to show node number in staad physical Modeler.

Hi everyone, As you know steel connection design in STAAD pro Advanced CONNECT doesn't accept built-up sections for some types of connections (for instance, Cap plate). In order to go around that, I have tried to modify the hot-rolled section database…

Dear friends, STAAD Pro reads only the moment at the element start point to design tapered steel section elements. Is there any way to fix it? Thanks

Hi everyone, I'm using footing support (Y direction and compression only). I have notice that it only work with some load cases (gravity) by not lateral load cases. Could you please take a look at the model and tell me what is the problem. thanks: …

I know WT are from W-shape beams, but is there a way to change how they labelled in Staad Pro? Example WT4x9 shows as W8x18 when reviewing model. Unless you double click to check member before it shows W8x18Tee. Also when you create the member for the…

Hi everyone, It is very weird that I am getting different utilization factors every time I run the analysis (The software picks different forces values at the tapered element) and for some reason, all sections have the same utilization value. Could…

400 KL FINAL WITHOUT STAIR change hieght.std EVERY TIME I M GETTING THE SAME PROBLEM Although I READ ALL THE POSTS REGARDING THIS ISUUE AFTR APPLYING SET NL COMMAND AND MEMORY COMMAND FACING THE SAME ISSUE.PLEASE PROVIDE VALID SOLUTION ASAP.

Hello, Here I m going to the attached model of my building and my problem is that when I ran this model in series 6 and staadpro ce update 7 after the analysis I'm getting the different results of R/F. you can checkout the result for beam no. 209…

Hey everyone! I'm looking at different STAAD files and need to know if I can figure out the exact time of creating these files in order to know if someone has copied someone else's job? thanks

HATTA CHLORINE BUILDING.std Plz, look into this file in this model the reinforcement required for columns no. 24 and 25 is very less as compare to another column. Please Check once what's wrong with this file becoz what I think the reinforcement required…

hen i will perform dynamic anaysis after assign property reduction factor than we got the error like this. *ERROR* STAR FILE MGR. ERROR NO. 6 DETECTED BY LIBREAD THIS ERROR MAY HAVE BEEN CAUSED BY INPUT DATA ERRORS OR PROGRAM LOGIC ERRORS. *** ERRORS…

I THINK I M FACING LOT OF ISSUE WITH THIS VERSION NOW ONE MORE ISSUE GOING TO DESIGN WATER TANK ONE GETTING ONE ERROR AFTER ANALYSIS. *** ERROR: MINIMUM DIMENSION OF COLUMN # 41 SHOULD NOT BE LESS THAN 20 TIMES THE DIAMETER OF THE LARGEST LONGITUDINAL…