Thermal cyclic loads
Am trying to model the effect of thermal loading on the backfill behind integral abutment by using Plaxis 2D. I modelled the concrete bridge deck as Linear Plate element and provide a prescribed displacement near the top of the abutment. The applied displacement…
Report generator issue with Material information when different material types for plates and anchors used in projects
Application
PLAXIS 2D
Issue status
Solved
First Affected Version
PLAXIS 2D CONNECT Edition V22 Update 2
Found in Version
PLAXIS 2D CONNECT Edition V22 Update 2
Fixed and Released in Version
PLAXIS 2D 2023.1
Issue…
Support capacity evaluation of a tunnel lining in PLAXIS 2D
Application
PLAXIS 2D
Version
PLAXIS 2D CONNECT Edition V22 Update 1 and later
Original Author
Richard Witasse - Application Engineer
Date created
01 November 2022
Date modified
01 November 2022
The project…
Optimize excavation calculation time for wall horizontal displacement criteria
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS 2D CONNECT Edition V22 PLAXIS 3D CONNECT Edition V22
Date created
23 September 2022
Date modified
23 September 2022
Original author
Hung Ho Manh - Bentley Technical Support…
Considerations for modelling a thick slab as a plate
Application
PLAXIS 2D PLAXIS 3D
Version
CONNECT Edition
Date created
15 February 2022
Date modified
15 February 2022
Original author
Faseel Khan - Bentley Technical Support Group
In PLAXIS 2D or 3D, a thick…
How to define and edit a material via the command line
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS CONNECT Edition V22
Date created
24 January 2022
Date modified
24 January 2022
Original author
Stefanos Papavasileiou - Bentley Technical Support Group
Introduction…
Error 111
Hello,
I am attempting to model a plate subject to an upward imposed displacement in a soil mass with two soil layers (see figure below). I activated the plate, the displacement and both soil polygons and then started the calculation.
This resulted…
Complex plate connections with interfaces may result in unexpected behaviour
Application
PLAXIS 2D PLAXIS 3D
Issue status
Open
First Affected Version
PLAXIS 2D PLAXIS 3D
Found in Version
PLAXIS 2D PLAXIS 3D
Fixed and Released in Version
Issue #
379391 (SW-47400)
Date created
06…
Non-linear deformation of structural elements
Application
PLAXIS 2D
Version
PLAXIS 2D
Date created
23 June 2016
Date modified
23 June 2016
This document verifies that the non-linear deformation of plates is treated correctly in PLAXIS. An elastoplastic 'M - k…
Performance of shell elements
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS 2D PLAXIS 3D
Date created
20 November 2012
Date modified
20 November 2012
Tunnel lining can be modelled as a beam in PLAXIS 2D and as a plate in PLAXIS 3D. By using this…
Bending of plates
Application
PLAXIS 2D PLAXIS 3D
Version
PLAXIS 2D PLAXIS 3D
Date created
14 November 2012
Date modified
14 November 2012
This document describes an example that has been used to verify the behaviour of plates in PLAXIS…
Shear deformation in structural elements
Application
PLAXIS 2D
Version
PLAXIS 2D
Date created
20 November 2012
Date modified
20 November 2012
PLAXIS takes into account the shear deformation in structural elements subjected to bending. For the verification…
Bending of axisymmetric plates
Application
PLAXIS 2D
Version
PLAXIS 2D
Date created
16 November 2012
Date modified
16 November 2012
In an axisymmetric analysis, plates may be used as circular plates. This document describes an example that has…