I am using AASHTO LRFD and IDOT does not have conventional longitudinal reinforcing in their PPC IL-Beams, but IDOT does consider bonded prestressing strands as sufficient in resisting the temporary tensile forces in prestressed concrete before losses…

I am performing a load rating of concrete box girders. The rating factors/tons is not displayed since the Inventory Design Load Rating Factor > 1. Is there an option to make the program display the factors even if the RF is greater than 1 or is that information…

Hello, I have 95 ft long and 12 ft wide abutment footing on 2 rows of piles. Abut stem is 88 ft long. How is the Leap program calculating Dist (ft) , dv, Vu and Phi Vc for X and Z ? I will appreciate the response. Thanks,

How does LEAP Conspan apply multiple presence factors if live load distribution factors are entered manually? If distribution factors are entered manually, is it up to the user to apply the multiple presence factor to the manually inputted distribution…

Hi I am designing 2 span continuous bridge with FIB 54 beams by opting full continuity, disregards restraining moments option. After analyzing and iteration of strand pattern and providing huge negative steel, i am not able to reduce tension stress…

What is the difference between the stresses given for the depression point in the "Release Stresses" box and the "Release Lifting Loops" box?

I hope this is an easy question regarding the shear stirrup spacing... Does the program insert a stirrup at the start location specified? For example, in the image below, is there a #3 2-legged stirrup provided at 0.00', 0.25', etc. or do the stirrups…

Hello, Camber and deflections are reported at 10th points along the beam. I am modelling a longer span which will require more than 10 screed points. Is there a way to toggle the number of points? Or do I have to interpolate? Thanks,

I am using Leap Bridge Concrete CONNECT Edition v17.01.01.07. I used ABC wizard to model a two span non continuous bridge (110'-104') with a 17.5 degree skew. The deck in span 1 is 66.6 ft while in span 2, it flares from 66.6ft in the interior bent to…

Is there a way to add a supplemental composite DW load for a poly wearing surface in Leap Concrete Bridge? I want to keep it separate from the Future Wearing Surface (Composite DW) load I already have. This is necessary to accurately calculate camber…

I am using CONSPAN in my design and have a couple of questions about the method in which the program performs calculations. Does CONSPAN design prestressed girders, at the interior supports, as reinforced concrete beams? According to AASHTO, LRFD 5.14…

How does LEAP Bridge Concrete calculate the reactions for DL-Comp. (DW)? I added up all the DW reactions and compared to a hand calc of utlities and overlay loads. The total DW is nearly 4 times greater than my hand calcs. I have 4 beam lines with 0.05…

In the Shear/Moment Envelope (&Reactions) Design output what is the difference between live load Max, Truck, and Lane? Is the max HL-93 including truck and lane loading? I have a 6 span continuous concrete superstructure.

When calculating the top and bottom stresses at the transfer and bearings, does LEAP take into account the development length? It seems that the stresses its calculating at the bearings and the transfer are higher than what they should be. Does LEAP use…

Hello, I'm designed a decked bulb tee and I notice that the composite section is the same as the beam section. The composite section should include the closure pours, but I can't seem to find a way to make this happen via the program or manual override…

I have a single span bridge using I-girders that I need close to the max amount of strands in. These are all straight strands, and I've had to debond to 4 different lengths from the end. The longest debond is 25' of my ~90' girder. When I look at the…

I'm modeling a PC/PS Girder Bridhge in LeapBridge, Conspan and RC-pier, based on California amendments to AASHTO. I am able to import my Vehicular LL and Fatigue LL from CONspan into RCpier, but RC-pier isnt letting me import the Permit Loads. Do you…

Release 9.0.0 of the LEAP Bridge Suite is scheduled to be released June 25, 2009. Several outstanding features are included in this release. Here is a brief list of some of the new features for this version : LEAP Bridge v 9.0.0 incorporates the…

LEAP Bridge v8.1.0 incorporates the following enhancements: • The ABC Wizard can now directly read in alignment, cross-section and profile information from LandXML files. The bridge model can now be generated very accurately directly utilizing…