When running analysis with and without P-delta I noticed there is a substantial increase in the axial column force when P-delta is applied. At the node 1 the difference is about 300 kips. What could be a reason for such an increase? Any insight is appreciated…

How do I install LEAP RC Pier v14.0019 with our selectserver? It used to install fine. Now when we try to install on a PC,it asks for the correct activation and selectserver info which we enter then it says its activated, When we click on the executable…

I have bent that is being constructed in two phases so some shrinkage will happen on the first phase before the next phase is constructed. In the final condition, I could assume the entire shrinkage strain is applied to both sections but that will be…

Does RC Pier check shear friction in the pier cap (AASHTO 5.7.4)? I've looked in the output reports and didn't see reference to this spec section. I've also looked in the application help interface and couldn't find it. Note: my application version…

Hello, Is LEAP Bridge concrete / RC-Pier capable of having a structure simple span for dead load and continuous for live load (SDCL)? Thanks.

Hi, There are cases where centrifugal forces produce a moment that actually counteracts the critical moment in the column, does RCPier consider effects due to vehicle cases without centrifugal forces as provisioned in AASHTO Spec (See below excerpt…

Hello, I have been experiencing a substantial amount of instability/crashing in LBC 20.00.00.46. The program will randomly freeze and become unresponsive. This happens when I run an analysis, look things up in the help manual, attempt to save, and many…

When checking Show P-delta Effects in the Analysis tab, are the values shown represent values with p-delta effect? For example, are the column/shaft moments magnified with p-delta factor in these load combinations (with a "C" on the end of the LC#)? If…

I am looking for pile reaction as piles integral with cap then save the file. next time open the file, it is back to "Cap as continuous beam" How can i fix this situation?

I am designing a hammerhead pier using the substructure module in LEAP Bridge Concrete. The geometry is a little odd...it's a hammerhead cap on a circular column. To compare the results for the cap design from the conventional sectional design & strut…

Does anyone have calculation verification for the live load auto-generation function in RC-PIER? Or has anyone else had problems verifying the LL output from RC-PIER?

I am using Leap Bridge Enterprise v14.00.00.09 in a Win7 environment. When I open the Geomath and Conspan modules, they work fine. When I open RCPier, it gets to a screen which says "Loading Project File" and then crashes, and it sometimes gives me a…

The attached file shows the output from the cap design module of RCPier v14. Can you tell me why there is a point where phi*Vn=504 and Vu=72.5 yet phi*Vn < Vu? Is this result spurious or is there a reason for this? Also, how can I tell what the most…

We are working a substructure design in which, due to the geometry of the roadway, it may be necessary to have the column rotated at an angle from the orientation of the pile footing on which it sits. In the past we've had to handle this via calculation…

One of the new features added to the latest RC-PIER is the comprehensive auto-generation of WS loads and load combinations per the FDOT SDG 2013: An option for WS load auto-generation is now offered under the “Loads” tab. FDOT strength and service…

A few RC-PIER users recently asked questions about the two analysis options in the abutment design and the related footing design reports. Here is some clarification. In abutment design, when "Cap as continuous beam" is selected for the frame analysis…

When manually inputting live loads into RC-Pier, how do you specify a lane load. According to the help.... "For manually input live loads in AASHTO LRFD, this screen behaves slightly different. When a live load case is added in LRFD mode and edited, the…

Hello all: I am having an extremely difficult time getting through my bridge design on LEAP bridge. Especially while working in GEOMATH and RC PIER. In GEOMATH: Problem #1: Back when I was trying to make minor adjustments to the geometry of the…