Hello,
It doesn't seem like there is a way to export the water age (maximum) results into a shapefile, since that is not a flextable column, which makes sense since the maximums are not necessarily associated with the same timestep. What is the recommended…
to
Eastern Time (US & Canada)
Online
All ACCELERATE virtual sessions are offered complimentary to all attendees.
This five-part webinar series provides water industry professionals innovative ideas for operating distribution systems at lower cost while maintaining or improving service...
As I know that SewerGEMS is equipped with water quality analysis, I have a stormwater network and would carry out the quality run, can somebody provide the guides and steps?
Thank you,
Mohamad
Dear All ,
Kindly i have a question , and i am a little bit confused about H2s Calculations in sewer gems.
First Of all i have seen this article and it understand it well :
Modeling septicity / hydrogen sulfide (H2S) .
In this article i…
Product(s):
WaterGEMS, WaterCAD
Version(s):
CONNECT Edition, V8i
Area:
Modeling
Problem
How can I define and use custom parameters and equations with Multi Species Extension (MSX), utilizing model parameters or results and…
Product(s):
OpenFlows TM FLOOD TM
Version(s):
CONNECT Edition (v 10.02.01.01)
Area:
Installation
Overview
The latest release of OpenFlows FLOOD introduces various updates to the previous version as well as addition of new…
Product(s):
WaterCAD, WaterGEMS
Version(s):
V8i, CONNECT Edition
Area:
Layout and Data Input
Problem
Is there a way to "reset" the water age to zero at a chlorine booster station?
Background
A PAX-RCS system for example…
Dear all,
As a beginner, I would like to have a technical support on flushing to improve disinfectant residual in the network. First, I used a long term EPS-240 hr- water quality run using chlorine residual as the indicator of quality. The simulation…
Hello,
I've been using WaterGems for a few days. I ran the quality model using constituent chlorine. I'm looking for a command that tells me for each simulation step how many nodes have a concentration below a certain threshold (in my case 0.2 mg/l…
Product(s):
WaterGEMS, WaterCAD
Version(s):
10.XX.XX.XX
Area:
Calculations
Problem
When attempting to compute a model using the Multi Species Extension (MSX), the following error occurs:
Could not solve reaction equilibrium…
Trying to use the Monochloramine Decomposition multi species analysis setup that was imported from the engineering library, but I keep getting an error that reads "Could not solve reaction equilibrium expressions". What am I setting up wrong in my Model…
Product(s):
SewerGEMS, CivilStorm
Version(s):
CONNECT Edition, V8i
Area:
Modeling
Problem
What are the capabilities of SewerGEMS and CivilStorm in terms of modeling water quality characteristics of sewer system?
Solution…
Product(s):
WaterGEMS, WaterCAD
Version(s):
CONNECT Edition, V8i
Area:
Output and Reporting
Problem
Water age results do not look right, or a strange or unexpected water age result is seen.
Solution
Water age results can…
Product(s):
WaterGEMS, WaterCAD
Version(s):
08.11.XX.XX
Area:
Modeling
Problem
Can a node be a constituent source? Problem ID#: 67478
Solution
Yes, to model a constituent source, you can set the "Is Constituent…
to
Eastern Time (US & Canada)
Virtual - register below
Register here
Join Bahtigul Varol, Consultant at Bentley Systems, to learn how WaterGEMS can help you maintain or improve water quality by performing a complete water quality analysis. The overview includes the impact of new tanks, extending the distribution...
to
Eastern Time (US & Canada)
Virtual - register below
Register here
Join Bahtigul Varol, Consultant at Bentley Systems, to learn how WaterGEMS can help you maintain or improve water quality by performing a complete water quality analysis. The overview includes the impact of new tanks, extending the distribution...
Product(s):
WaterGEMS, WaterCAD
Version(s):
10.00.xx.xx, 08.11.xx.xx
Area:
Modeling
Problem
How does WaterGEMS and WaterCAD calculate the water age in a looped system? For instance, a case where flow from two pipes in converging…
Product(s):
WaterGEMS, WaterCAD
Version(s):
CONNECT Edition, V8i
Area:
Modeling
Introduction
This article has general information on getting ready to run a constituent analysis in WaterGEMS or WaterCAD.
You can…
Applies To
Product(s):
WaterGEMS, WaterCAD
Version(s):
CONNECT Edition,V8i
Area:
Modeling
Original Author:
Sushma Choure, Bentley Technical Support Group
Problem
How to model DBP formation in WaterGEMS or WaterCAD…
If multiple water sources serve your customers, or if you have multiple constituents flowing in your pipes, you may be managing and computing separate runs to track them. Did you know that the Water Quality Batch Run tool can be used to compute and view…
Product(s):
WaterGEMS, WaterCAD
Version(s):
CONNECT Edition, V8i
Area:
Calculations
Problem
After setting up a trace, age or constituent analysis, There are no results for calculated trace, age or constituent results…
Applies To
Product(s):
WaterCAD, WaterGEMS
Version(s):
08.11.xx.xx, 10.xx.xx.xx
Area:
Calculations
Original Author:
Scott Kampa, Bentley Technical Support Group
Problem
There is a discrepancy…
Product(s):
WaterGEMS, WaterCAD
Version(s):
CONNECTION Edition, V8i 08.11.05.61 and greater
Area:
Modeling
Author:
Dr. Tom Walski
Background
The problem with mixing chlorine (free chlorine, HOCl) with…
Hello Jamal,
The Bentley LEARNserver offers the learning path "Water Quality Modeling using WaterCAD or WaterGEMS" which includes the course titled "Multisource Mixing, Chlorine Residual and Age Analysis".
There is a chlorine water quality tutorial…
Product(s):
Bentley WaterCAD, WaterGEMS, Hammer
Version(s):
V8i, Connect Edition
Area:
Output and Reporting
Problem
The concentration of my constituent in the pipe that is directly downstream of my tank, which is my concentration…