I merged two surfaces together to create the existing surface for my design. Upon cutting cross sections I see that both surfaces are displayed instead of just the merged surface. I'm new to OpenRoads (2020 Release 3). Is this caused by the way I merged…

Hi. I'm using PowerCivil. Whenever I try to open Cross Section view to see pavements location at different stations, the chosen window is empty. And it doesn't matter whether I choose Corridors or Alignment to create cross sections. Is there anything…

Hello. I have 2 questions: 1)After I open the Cross Section View, the view it s mirrored like this: Left is in the right side and right in the left side How can I solve that? 2) Where can I change the stationing in profile view? I need stations…

I am stuck with using InRoads cross-sections on a particular project, but I am considering re-creating the geometry and terrains in ORD and using ORD for the drainage design so I can take advantage of ORD efficiencies. But I must be able to display this…

Does anyone know why my Right of Way labels aren't displaying when I cut cross sections to sheets but they show up in my dynamic cross section view? Below are a couple of pictures as-is from Dynamic View vs Cross Section Sheets

Running ORD 2021 R1. I have created a closed mesh for select fill and referenced it into my cross section container file. I am trying to see if it would be possible to hatch the area inside the closed mesh in the drawing model, similarly to how components…

When I create cross section named boundaries, sometimes there is information outside the fixed left and right offset widths that needs to be shown. I have been manually extending the named boundaries in 3d view (before creating sheets & annotations…

I am creating a boat load of cross sections in multiple files. While the cross sections themselves are coming in fine, when they are laid out on the sheet, they are uncentered and its quite tedious to have to keep manually re-entering a 100+ sheets (especially…

Hello! Does anyone know a way to shift a cross section named boundary in the drawing model? In this example, I simply want to shift my named boundary down in order to center my section better without having to recut a new named boundary. This is in…

Hi. I'm using PowerCivil. After creating cross-section at different chainage points, I need to annotate them as in the sketch below: in points, marked with red arrows, I need to specify point's distance from the central axis and the elevation. I also…

Hello, I'm using Openroads Designer and am trying to update named boundaries for cross section views. I added a 3D feature line in a reference file that is set up to display a cell when shown in cross section view (more specifically, a right-of-way…

Hi. I'm using PowerCivil. How can I insert independetn line in cross section, I mean - I need a vertical line (no matter what the "h" is), which consists of two defined points, where bottom point follows (defined in point control) to linear geometry…

We are using OpenRoads to generate plan/profile and cross section drawings within a Projectwise environment. The sheets are created within and OpenRoads 2D model seeds. To allow for Projectwise to generate pdf renditions, the file must be saved and…

As you can see below the offset's are not correct. I only have it displayed to the 10th but it is off by 0.0615088. The elevation is correct. The offsets are suppose to be 4.0' and 17.0' each side of the center line. I don't know if I need to…

Does anyone know of a way to verify the numbers we're getting for earthwork? Either by EAV or prismoidal? I have lobbed the question out here before, but the only way I know to check is to check the drawing cross section model and use the 'flood' option…

Yesterday I worked in a cross section model and annotated it. Yesterday, my only issue was that my Cross section Navigator didn't work. The error below appears. -the cross section cell was in place and i am in the correct gpk Today when I went…

Hello all. I am and FDOT user making the switch from SS10 to ORD Connect edition. I know that the cross sections are stored in the model, however, if we have to add specific features at one specific cross section, how do we do so without manipulating…

Hi Everyone, I am currently trying to export my cross sections from open roads designer to DWG auto cad format. However no matter what setting I try on my export the DWG files seem to contain the 3D model (as shown) I have tried disabling 3D settings…

Hello, I updated my XS annotation group in the .dgnlib file at this location (C:\FDOTConnect\Organization-Civil\FDOT\Dgnlib\Feature Definitions) But when I cut my cross sections, it doesn’t reflect all the changes I made. How can I make the…

Hello, I updated my XS annotation group in the .dgnlib file at this location (C:\FDOTConnect\Organization-Civil\FDOT\Dgnlib\Feature Definitions) But when I cut my cross sections, it doesn’t reflect all the changes I made. How can I make the…

Hey, Has anyone else ran into this problem? I'm using the same cross section annotation on every one of my models, and sometimes the EAV table populates and other times the EAV table does not populate on the cross section. It will be along the same…

Hi Everyone, Our firm is having a recurring problem with our cross section labeling. We are creating our cross sections from corridor models. Once we have the cross sections cut, we only have 50-75% of the necessary cross hairs populated to annotate…

I am migrating to ORD from SS10. One thing I'm missing for cutting XS sheets is the XS from linestring tool that was available in SS10. I'm needing to cut a cross section at a proposed culvert that is on a skew and I would like to have the XS also show…

Hi, While exporting Cross sections to dwg format, EAV Table values are showing 0 in dwg file. Please suggest any solution for this error. Thanks in advance, Mintu Mondal