• 02. Reason #2 - Why are the all load case values 0.00 for a particular node point in AutoPIPE's Reference Point loads sub-report?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version Dec 2022 12.08.03.015 Problem: For a given node point (A31), why are almost all of the load case values 0.00 in Reference…
    • 9 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 01. Reason #1 - Why are the all load case values 0.00 for a particular node point in AutoPIPE's Reference Point loads sub-report?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version Sept. 2017 11.01.00.17 Problem: For a given node point (B03F), why are the all load case values 0.00 in Reference Point…
    • 9 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 19. Why saddle support reactions are 0.00 in an AutoPIPE Vessel output report?

    Tanaji Gaikwad
    Tanaji Gaikwad
    Applies To Product(s): AutoPIPE Vessel Version(s): ALL Area: Report Date Logged & Current Version June 2018 40.06.00.07 Problem: Why saddle support reactions are 0.00 in an AutoPIPE Vessel output report? Example…
    • 2 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 11. Support forces = 0.00 in AutoPIPE's results, why?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Results Date Logged & Current Version June 2019 12.01.00.10 Problem: Why are the support forces = 0.00? Solution: Question: Name reasons why support…
    • 9 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 08. Why are the results for Creep Rupt = 0.00, Blank, or not printed in the output report for En13480 piping code in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculation Date Logged & Current Version April. 2018 11.03.00.08 Problem: Why are the results for Creep Rupt = 0.00, Blank, or not printed in the output…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • AutoPIPE known issue - Defect 805881

    Mike Dattilio
    Mike Dattilio
    Applies To Product: AutoPIPE First Affected Version: 11.02.00.08 Found in Version: 11.02.00.10 Fixed and Released in Version: 11.03.00.xx Area: All Severity: High Backlog…
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 05. No load information was exported from AutoPIPE to STAAD. Why?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Export Date Logged & Current Version April. 2018 11.03.00.08 Problem: It appears that the loads in AutoPIPE are not being exported to STAAD. Why? Solution…
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 05. Results for DNV code combinations Collapse and Prop Buck are 0.00 or very small when using AutoPIPE

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculations Date Logged & Current Version April. 2014 09.06.00.15 Problem: The results for DNV code combinations Collapse and Prop Buck are 0.00 or very…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • Q. Even with "zero loads and moments"; still AutoPIPE's Flange analysis results says the connection fails, why?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE, Version(s): ALL Area: Flange analysis Original Author: Bentley Technical Support Group Dec 2014, AutoPIPE V8i 09.06.01.10 Problem: Even with "zero loads and…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 01. Hoop Stress Allowable is 0.00 (zero) for a piping system analyzed in AutoPIPE per En 13480, why?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL Area: Results Original Author: Bentley Technical Support Group Date Logged & Current Version Mar. 2015 09.06.01.11 Problem: Hoop…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02. AutoPIPE Results Grids or Output Reports are found to be Zero (0.00) or Blank

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE, Version(s): ALL Area: reports / results Original Author: Bentley Technical Support Group Problem: AutoPIPE: results are 0 / zero Description: when viewing results…
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 05. Why are hoop stresses 0.00 / None in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Results Original Author: Bentley Technical Support Group Date Logged & Current Version Oct. 2016 10.01.00.09 Problem: Why are hoop stresses 0.00…
    • over 2 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 08. Why are the Stress results for ASME B31.8 (2014) 0.00 in AutoPIPE's results Grids and output reports?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i, CONNECT; Area: analysis Original Author: Bentley Technical Support Group Date Logged & Current Version June. 2016 10.01.00.09 …
    • over 1 year ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 04. Dynamic Time history analysis results are 0.00 in AutoPIPE output report, why?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i, CONNECT; Environment: N/A Area: Subarea: Original Author: Bentley Technical Support Group Date Logged…
    • over 7 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • View related content throughout AutoPIPE
  • More
  • Cancel