• 15. How are DNVGL-F101 offshore 2017 ASD calculations per GrT1P1 performed in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Stress Calculations Date Logged & Current Version April 2023 23.00.00.230 Problem: How does AutoPIPE calculate DNVGL-F101 offshore 2017 ASD (Allowable Stress…
    • 5 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 01. Why is Von Mises stress calculations different than automatically calculated ASD in AutoPIPE ?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculations Date Logged & Current Version April. 2018 11.03.00.08 Problem: By calculating the Von Mises stress in a separate way, the result it is different…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02. DNV 2012 references a new definition of bending, but AutoPIPE help is different

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculations Date Logged & Current Version April. 2014 09.06.00.15 Problem: In the AutoPIPE on line manual (help/contents/code/DNV 2012/ASD) there are references…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 03. ASD results are lower than the hoop stress results

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculation Date Logged & Current Version April. 2014 09.06.00.15 Problem: AutoPIPE's (automatic) calculation of the ASD is lower than the hoop stress and…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 05. Results for DNV code combinations Collapse and Prop Buck are 0.00 or very small when using AutoPIPE

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculations Date Logged & Current Version April. 2014 09.06.00.15 Problem: The results for DNV code combinations Collapse and Prop Buck are 0.00 or very…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 08. Explain Load Controlled Buckling check “stress value” and "allowable value” in AutoPIPE's output report

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version April. 2014 09.06.00.19 Problem: Regarding the LCC (Load Controlled condition) check according to DNV 2012 (section…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 10. Max Utilization Ratio for combined load case was less than Max Utilization Ratio for a single load case in an AutoPIPE report, why?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculations Date Logged & Current Version April. 2014 09.06.00.15 Problem: Original issue description: strength check on a pipe (ex. 18 inch) riser under…
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 03. What are the maximum longitudinal stress results for General Pipe stress different from the DNV code calculations when using AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2017 11.00.00.22 Problem: Could you please explain why the maximum longitudinal…
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • View related content throughout AutoPIPE
  • More
  • Cancel