• 03. Where to change the values for Clamp Wb and Wba for BS En 13445 2021 using AutoPIPE Vessel?

    Mike Dattilio
    Mike Dattilio
    Answer: These values are not user input values or calculated values by the program. These values are referenced by the Allowable Bolt Load table at Room Temp or At Design Temp for the clamped flanges. One can review the referenced table in AutoPIPE…
    • 22 days ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02. How to calculate Von Mises category combinations allowable using AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Date Logged & Current Version Dec 2022 12.08.03.015 Problem: How to calculate Von Mises category combinations allowable using AutoPIPE? Solution: Open…
    • 9 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 00. How to calculate ASME B31.3 2010 Allowables in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Calculations Date Logged & Current Version June 2022 12.08.00.063 Problem: How to calculate ASME B31.3 2010 Allowables in AutoPIPE? Solution: ASME B31…
    • over 1 year ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 05. Allowable stresses input by user for test conditions in AutoPIPE Vessel

    Tanaji Gaikwad
    Tanaji Gaikwad
    Applies To Product(s): AutoPIPE Vessel Version(s): V8i, CONNECT Environment: N/A Area: Analysis Subarea: Original Author: Bentley Technical Support Group Date…
    • 2 months ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 08. Explain Load Controlled Buckling check “stress value” and "allowable value” in AutoPIPE's output report

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Report Date Logged & Current Version April. 2014 09.06.00.19 Problem: Regarding the LCC (Load Controlled condition) check according to DNV 2012 (section…
    • over 3 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 09. What to do when dynamic Response Spectrum exceeds a code allowable when using AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): ALL; Area: Reports Original Author: Bentley Technical Support Group Date Logged & Current Version Feb. 2017 11.00.00.22 Problem: What to do when dynamic Response…
    • over 5 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • AutoPIPE known issue - defect 135343 (8472)

    Mike Dattilio
    Mike Dattilio
    Applies To Product: AutoPIPE First Affected Version: 08.06.00 Found in Version: 09.01.01.02 Fixed and Released in Version: 09.03.00.08 Area: Calculations Severity: Critical …
    • over 4 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • AutoPIPE known issue - defect 407514

    Mike Dattilio
    Mike Dattilio
    Applies To Product: AutoPIPE First Affected Version: 09.01.00 Found in Version: 10.00.00.10 Fixed and Released in Version: 10.01.00.08 Area: Calculations Severity: Critical …
    • over 4 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • AutoPIPE known issue - defect 138808 (10782)

    Mike Dattilio
    Mike Dattilio
    Applies To Product: AutoPIPE First Affected Version: 09.04.01 Found in Version: 09.04.01.05 Fixed and Released in Version: 09.05.01.02 Area: Calculations Severity: Critical …
    • over 4 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • 02. How to calculate the ASME NC 2007 allowable for Service Level C with GR + Seismic reversing Dynamic loads in AutoPIPE?

    Mike Dattilio
    Mike Dattilio
    Applies To Product(s): AutoPIPE Version(s): 2004, XM, V8i, CONNECT; Environment: N/A Area: Original Author: Bentley Technical Support Group Date Logged & Current Version Aug. 2016 10.01.00.09 Problem…
    • over 7 years ago
    • AutoPIPE
    • AutoPIPE Wiki
  • View related content throughout AutoPIPE
  • More
  • Cancel