• Save the last # Design States

    Jared Hilt
    Jared Hilt
    • New on Wed, May 11 2022
    • 0 Comments
    There should be an option to automatically save the last two or three designed states or be able to ctrl z back to them. Could be saved as separate files, or just maintain the data internally. Preferrably would keep the data internal. I hate when I flip...
    • Wed, May 11 2022 10:59 AM
  • RAM Elements - GUI - Stretch all columns by stretching end column

    RFreund
    RFreund
    • New on Thu, Nov 11 2021
    • 3 Comments
    Have the ability to increase the width of all columns by stretching the last column. See screenshot below:
    • Thu, Nov 11 2021 11:04 AM
  • Separate Analysis per load

    Jared Hilt
    Jared Hilt
    • New on Wed, May 11 2022
    • 1 Comment
    Many times I will change one load, for example a seismic load which is palced at the Ridge. Then I have to reanalyze and redesign the entire model, every load case. There should be a way to analyze only the affected load cases and redesign only the affected...
    • Wed, May 11 2022 4:28 PM
  • Nodal Displacement Font Color

    Travis Hall
    Travis Hall
    • Under Review on Thu, Mar 10 2022
    • 2 Comments
    In RAM Elements, under the "View" menu, there is a "Nodal displacement" option that can be toggled to see how much displacement exists at a particular node (for example, it could display "Ty = 1.00 [in]"). Currently, depending on what font is used, it...
    • Wed, Feb 16 2022 12:36 PM
  • RAM Elements Retaining Wall Summary Results

    NAyche
    NAyche
    • Under Review on Thu, Mar 10 2022
    • 2 Comments
    Hello, In RAM Elements retaining wall module, it would be nice if we can see a summary of the stability results on screen, so we don't have keeping opening the report. That would be the sliding ratio, overturning ratio, bearing pressure/capacity. This...
    • Thu, Mar 3 2022 3:16 PM
  • Ability to do anything while Analyzing and designing

    Jared Hilt
    Jared Hilt
    • New on Tue, Dec 13 2022
    • 0 Comments
    When a model is analyzing or designing, we currently have to sit and wait. It would be nice to be able to do things in the editor (viewing only of course) while we ware waiting on the model to finish.
    • Tue, Dec 13 2022 1:34 PM
  • Masonry Wall Shear Strength Discrepancy

    Seth Engel
    Seth Engel
    • New on Fri, Jul 23 2021
    • 1 Comment
    I am using the standalone masonry wall design module, and am unable to verify the shear strength ϕVn presented in the report. Hand calculations by multiple engineers at my firm yield a significantly different value. Can you please provide the formulas...
    • Fri, Jul 23 2021 9:07 AM
  • Add optional check box to segment at distance

    Jared Hilt
    Jared Hilt
    • New on Mon, May 16 2022
    • 0 Comments
    Many times I would like to continue to segment the member at a certain distance until the distance is less than that specified distance. this can be implemented with a simple check box.
    • Mon, May 16 2022 9:55 AM
  • Concrete confinement

    Sepehr Movaghati
    Sepehr Movaghati
    • New on Thu, Oct 20 2022
    • 0 Comments
    RAM ELEMENT tilt-up module. Modeling a wall with two openings. The compression stresses at opening jambs exceed 0.06f'c. We have ties #3@8"o.c. at opening jambs. Can we model ties?
    • Thu, Oct 20 2022 10:04 AM